Figure 1004 Hammer Union — Butt Weld, Sour Gas Service, 7,500 psi

Figure 1004 hammer union, sour gas service, butt weld ends. 5" to 6", rated 7,500 psi (517 bar). Full size table with weights and dimensions on this page.
Key features
- Figure Number: 1004
- Union Type: Union
- End Connection: Butt weld
- Service Class: Sour gas service
- Working Pressure: 7500 psi
- Nominal Size Range: 5" to 6"
- Seal Arrangement: Lip-type elastomer seal
- Figure Number
- 1004
- Union Type
- Union
- End Connection
- Butt weld
- Service Class
- Sour gas service
- Working Pressure
- 7500 psi
- Nominal Size Range
- 5" to 6"
Product description
The Figure 1004 is a 5 in and 6 in butt weld union that carries the lip-type elastomer seals used in the smaller unions instead of the O-ring the 5 in and 6 in Figure 1002 uses.
Applications
High-pressure lines at 5 in and 6 in where a Figure 1002 O-ring union is difficult to make up square.
Construction and sealing
- Lip-type elastomer seals, in place of the O-ring used by the 5 in and 6 in Figure 1002. An O-ring union of that size has to be made up perfectly square or it gives trouble; the lip seal is what the Figure 1004 exists to fix.
- Butt weld ends, 5 in and 6 in.
- Available in standard service or sour gas trim.
- Sealing: Lip-type elastomer seal.
Working pressure
7,500 psi (517 bar) cold working pressure.
Sour gas service unions are supplied in H2S trim and are rated below the standard service union of the same figure number wherever the source publishes a separate H2S rating. Confirm the service class, the trim and the certification you need on your enquiry - we quote against the line specification.
How a hammer union makes up
A hammer union is a three-piece connection. A male sub and a female sub carry the two line ends, and a wing nut turns on a thread cut into the male sub and pulls a shoulder on the female sub down onto the seat. The lugs standing proud of the nut are struck with a hammer to tighten it, which is where the name comes from — the joint is made up and broken out with a sledgehammer rather than a wrench, so a line can be rigged and stripped quickly in the field. The seal is made by the seat, not by the thread: the nut only supplies the load that holds the two seating faces together. That is why a union will leak from a scored seat or a perished seal long before the thread is at fault, and why a worn union is usually a sub or a seal replacement rather than a scrap part.
Specifying one
Four things fix a hammer union: the figure number, which sets the pressure class and decides what it will mate with; the service class, standard or sour gas; the end connection, threaded or butt weld; and the nominal size. Figure numbers are an industry series, so a union of the same figure and size from another maker will mate — but the pressure rating stamped on the union is what governs, not the figure number on its own. Send us the line specification and we will confirm the match before quoting.
Sizes and part numbers
Published in 5" to 6" with butt weld ends. Every orderable size, its weight, its dimensions and its working pressure are in the size table on this page. Where dimensions and weight are critical, ask us to confirm them against the build before you order.
Identification
| Parameter | Value |
|---|---|
| Figure Number | 1004 |
| Union Type | Union |
| End Connection | Butt weld |
Performance
| Parameter | Value |
|---|---|
| Service Class | Sour gas service |
| Working Pressure | 7500 psi |
| Working Pressure | 517 bar |
Dimensions
| Parameter | Value |
|---|---|
| Nominal Size Range | 5" to 6" |
Sealing
| Parameter | Value |
|---|---|
| Seal Arrangement | Lip-type elastomer seal |
Shipping & lead time
Sizes & part numbers
2 sizes- Indus part no.IH-HU-1004-BW-SOUR-0500
- Nominal size
- 5"
- End connection
- 5" butt weld
- A (mm)
- 152.4
- B (mm)
- 209.6
- Weight (g)
- 38600
- Working pressure (bar)
- 517
- Indus part no.IH-HU-1004-BW-SOUR-0600
- Nominal size
- 6"
- End connection
- 6" butt weld
- A (mm)
- 184.2
- B (mm)
- 238.3
- Weight (g)
- 63600
- Working pressure (bar)
- 517
A — Dimension A on the manufacturer dimension drawing. B — Dimension B on the manufacturer dimension drawing. Ask us for the dimension drawing if you need it stamped.
Working pressure is the manufacturer’s published rating for the fitting itself. An assembly is limited by its lowest-rated component, so check it against the hose, the tube and the port you are mating to.
What is a Figure 1004 butt weld sour gas hammer union used for?▾
How do I read the part number IH-HU-1004 on a sour Figure 1004 union?▾
What is the working pressure of the sour Figure 1004 hammer union?▾
What sizes does the sour Figure 1004 union come in?▾
Why choose the Figure 1004 over the 5" or 6" Figure 1002?▾
What seal and material does the sour Figure 1004 union use?▾
Can I use a standard Figure 1004 union in H2S service?▾
Which unions will mate with a sour Figure 1004 hammer union?▾
How is a sour Figure 1004 union made up and serviced?▾
How does the sour Figure 1004 differ from the standard service version?▾
What documents come with the Figure 1004 butt weld sour gas hammer union?▾
Do you have Figure 1004 butt weld sour gas hammer unions in stock in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
The same part, in the designations used across European and Gulf trade catalogues.
- de
- Hammerverschraubung Verschraubung
- fr
- union à marteau union
- es
- unión de martillo unión
- it
- giunto a martello giunto
From the blog
Written about this range
Oilfield & pressure control
Well service and stimulation hose: frac, acidizing, well test and flare boom lines
Stimulation and frac lines run at 15,000 psi, well test lines carry sour produced fluid, and flare boom hose sees 200 °C. What each well service hose is built from, and why the liner is the decision.
4 min read
Oilfield & pressure control
Hammer union figure numbers explained: pressures, seals and sour service from Figure 100 to 2202
A hammer union figure number mostly tells you its working pressure — 602 is 6,000 psi, 1502 is 15,000 psi — but not always, and some sizes are derated. How to read the figure, the seal behind it and the sour-service versions.
6 min read







