Embedded G-Fin Tubes

Fin strip wound into a helical groove cut in the base tube, with the groove edges rolled back to lock the fin root. Made to API 661 / ISO 13706, ASTM A179, ASTM A192. Supplied from Dubai with an Indus part number for each size and mill test certificates on request.
Key features
- Product type: Embedded G-Fin Tubes
- Construction: Strip wound into a helical groove; groove edges peened/rolled back to lock the fin root
- Standards: API 661 / ISO 13706, ASTM A179, ASTM A192, ASTM A210, ASTM A106 B
- Base tube material: Carbon steel A179, A192, SA210 A1/C, A106 B; Stainless TP304/304L, TP316/316L; Duplex S31803; Copper C12200, Cu-Ni 90/10, 70/30
- Fin material: Aluminium 1060/1100; Copper; Carbon steel
- Outside diameter: 15.88–38.1 mm
- Wall thickness: ≥2.11; must be thicker than for wrap-on fins because the groove removes wall
- Fin geometry: height 9.5–16 (3/8, 1/2, 5/8 in); thickness 0.38–0.51 (0.015/0.016/0.020 in); range 0.3–0.65; density 6–12 FPI (236–472 fins/m)
- Maximum service temperature: ≈400 °C typical maker limit (published 380–415 °C)
- Product type
- Embedded G-Fin Tubes
- Construction
- Strip wound into a helical groove; groove edges peened/rolled back to lock the fin root
- Base tube material
- Carbon steel A179, A192, SA210 A1/C, A106 B; Stainless TP304/304L, TP316/316L; Duplex S31803; Copper C12200, Cu-Ni 90/10, 70/30
- Fin material
- Aluminium 1060/1100; Copper; Carbon steel
Product description
Fin strip wound into a helical groove cut in the base tube, with the groove edges rolled back to lock the fin root. Embedded fins are the highest-temperature aluminium-fin type, so they go on the hot inlet passes of air coolers in refineries and gas plants. The groove takes wall from the tube, so the base tube is heavier than for wrapped fins.
Specification
- Maximum service temperature: ≈400 °C typical maker limit (published 380–415 °C)
- Base tube OD (mm): 12.7–50.8 (standard table 5/8–1 1/2 in)
- Base tube wall (mm): ≥2.11; must be thicker than for wrap-on fins because the groove removes wall
- Groove depth (mm): ≈0.4
- Fin height (mm): 9.5–16 (3/8, 1/2, 5/8 in)
- Fin thickness (mm): 0.38–0.51 (0.015/0.016/0.020 in); range 0.3–0.65
- Fin density: 6–12 FPI (236–472 fins/m)
- Fin material: Aluminium (1060/1100), copper; carbon steel possible
- Bond type: Strip wound into a helical groove; groove edges peened/rolled back to lock the fin root
- Max length (m): 15–18
- Atmospheric corrosion resistance: Low: exposed steel between fins
Standards
API 661 / ISO 13706, ASTM A179, ASTM A192, ASTM A210, ASTM A106 B. Equivalent grades across ASTM, EN, DIN, JIS and GB/T standards are indicative; we check them against each tender.
Materials
- Tube: Carbon steel A179, A192, SA210 A1/C, A106 B; Stainless TP304/304L, TP316/316L; Duplex S31803; Copper C12200, Cu-Ni 90/10, 70/30
- Fins: Aluminium 1060/1100; Copper; Carbon steel
Testing and documents
- Base tube tests per its spec
- Fin pull-out/bond check per maker QA
- Mill test certificate to EN 10204 3.1 on request; third-party inspection can be arranged against your inspection and test plan
Where it is used
- Cyclic-temperature ACHE services where owner specs call for embedded fins
- High-temperature ACHE inlet passes (above ~315 °C) in refineries and gas plants
Sizes
5 sizes, each under its own Indus part number in the size table. The table lists typical sizes for the range; other sizes are made on request.
Ordering
Quote the Indus part number from the size table, or send the standard and grade, the outside diameter and wall (BWG or millimetres, minimum or average wall), the length and the quantity, with the fin type, material, height, thickness and fins per inch, and the bare length at each end. We quote with the mill certificates and the inspection you need.
Identification
| Parameter | Value |
|---|---|
| Product type | Embedded G-Fin Tubes |
| Construction | Strip wound into a helical groove; groove edges peened/rolled back to lock the fin root |
Compliance
| Parameter | Value |
|---|---|
| Standards | API 661 / ISO 13706, ASTM A179, ASTM A192, ASTM A210, ASTM A106 B |
Construction
| Parameter | Value |
|---|---|
| Base tube material | Carbon steel A179, A192, SA210 A1/C, A106 B; Stainless TP304/304L, TP316/316L; Duplex S31803; Copper C12200, Cu-Ni 90/10, 70/30 |
| Fin material | Aluminium 1060/1100; Copper; Carbon steel |
Dimensions
| Parameter | Value |
|---|---|
| Outside diameter | 15.88–38.1 mm |
| Wall thickness | ≥2.11; must be thicker than for wrap-on fins because the groove removes wall |
| Fin geometry | height 9.5–16 (3/8, 1/2, 5/8 in); thickness 0.38–0.51 (0.015/0.016/0.020 in); range 0.3–0.65; density 6–12 FPI (236–472 fins/m) |
| Length | 15–18 m maximum single length |
| Size table | Typical sizes — other sizes on request |
Performance
| Parameter | Value |
|---|---|
| Maximum service temperature | ≈400 °C typical maker limit (published 380–415 °C) |
Quality
| Parameter | Value |
|---|---|
| Testing | Base tube tests per its spec; Fin pull-out/bond check per maker QA |
| Certification | Mill test certificate to EN 10204 3.1 on request; third-party inspection by arrangement |
Application
| Parameter | Value |
|---|---|
| Typical services | Cyclic-temperature ACHE services where owner specs call for embedded fins; High-temperature ACHE inlet passes (above ~315 °C) in refineries and gas plants |
Shipping & lead time
Sizes & part numbers
5 sizes- Indus part no.IH-TF-GF-GFN-0159
- O.D. (mm)
- 15.88
- O.D. (in)
- 5/8
- Wall (mm)
- ≥2.11
- Fin O.D. (mm)
- 34.93
- Fin height (mm)
- 9.53
- Fin thickness (mm)
- 0.41
- Fins per inch
- 6–12
- Max. length (m)
- 15
- Indus part no.IH-TF-GF-GFN-0190
- O.D. (mm)
- 19.05
- O.D. (in)
- 3/4
- Wall (mm)
- ≥2.11
- Fin O.D. (mm)
- 44.45
- Fin height (mm)
- 12.7
- Fin thickness (mm)
- 0.41
- Fins per inch
- 6–12
- Max. length (m)
- 15
- Indus part no.IH-TF-GF-GFN-0254
- O.D. (mm)
- 25.4
- O.D. (in)
- 1
- Wall (mm)
- ≥2.11
- Fin O.D. (mm)
- 50.8
- Fin height (mm)
- 12.7
- Fin thickness (mm)
- 0.41
- Fins per inch
- 6–12
- Max. length (m)
- 15
- Indus part no.IH-TF-GF-GFN-0254-B
- O.D. (mm)
- 25.4
- O.D. (in)
- 1
- Wall (mm)
- ≥2.11
- Fin O.D. (mm)
- 57.15
- Fin height (mm)
- 15.88
- Fin thickness (mm)
- 0.41
- Fins per inch
- 6–12
- Max. length (m)
- 15
- Indus part no.IH-TF-GF-GFN-0381
- O.D. (mm)
- 38.1
- O.D. (in)
- 1 1/2
- Wall (mm)
- ≥2.11
- Fin O.D. (mm)
- 69.85
- Fin height (mm)
- 15.88
- Fin thickness (mm)
- 0.41
- Fins per inch
- 6–12
- Max. length (m)
- 15
O.D. (mm) — Outside diameter of the tube or pipe in millimetres. O.D. (in) — The same outside diameter in inches, as the trade orders it. Wall (mm) — Wall thickness in millimetres: minimum or average wall per the governing standard and the order. Fin O.D. (mm) — Outside diameter over the fins in millimetres. Fin height (mm) — Height of the fin above the tube surface in millimetres. Fin thickness (mm) — Fin strip or plate thickness in millimetres. Fins per inch — Fin density in fins per inch; a band means any density in it can be made. Max. length (m) — Longest single length usually made, in metres; longer on request.
These are typical sizes for the range, not a full mill list. Other diameters, walls, fin geometries and lengths are made to order: tell us the standard and grade, the O.D. and wall, and the length you need. Mill test certificates to EN 10204 3.1 are available on request.
What are Embedded G-Fin Tubes used for?▾
How do I read an Indus part number for Embedded G-Fin Tubes, such as IH-TF-GF-GFN-0159?▾
What sizes do Embedded G-Fin Tubes come in?▾
What do I need to send to order Embedded G-Fin Tubes to the right size and grade?▾
What is the maximum service temperature of Embedded G-Fin Tubes?▾
What tests and certificates come with Embedded G-Fin Tubes?▾
Which materials and grades are Embedded G-Fin Tubes available in?▾
Which standards apply to Embedded G-Fin Tubes?▾
What do Embedded G-Fin Tubes connect to or fit with?▾
How should Embedded G-Fin Tubes be inspected on receipt and stored?▾
How are Embedded G-Fin Tubes shipped, and can they be exported from Dubai?▾
Do you keep Embedded G-Fin Tubes in stock in Dubai?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog
Written about this part
Heat-transfer tubes
Finned and seamless heat-transfer tube: a buyer’s guide
How to specify tube for air coolers, shell-and-tube exchangers, condensers, boilers and fired heaters: the standard and grade, OD and wall, length, fin type and bend schedule — and what to send with an enquiry so the quotation matches the data sheet.
6 min read
Heat-transfer tubes
Extruded fin tube for coastal and offshore air coolers
Extruded aluminium fins cover the liner tube completely, which is why they are the usual choice for air coolers near the sea, offshore and in LNG and gas plants. How extruded tube is made, its limits, liner choices and sizes.
3 min read
Heat-transfer tubes
Types of finned tubes: L, LL, KL, G-fin, extruded or welded?
Wound, embedded, extruded and welded fins differ in how the fin is held to the tube — and that bond sets the temperature, the corrosion protection and the price. How to choose a fin type for an air cooler, economiser or fired heater.
6 min read
