Heat Exchanger Baffles and Support Plates

Segmental baffles and tube support plates for shell-and-tube exchangers, stack-drilled to TEMA hole clearances and your drawing. Made to TEMA, HEI Standards for Closed Feedwater Heaters. Supplied from Dubai with an Indus part number for each size and mill test certificates on request.
Key features
- Product type: Heat Exchanger Baffles and Support Plates
- Construction: Machined from plate or forging to your drawing
- Standards: TEMA, HEI Standards for Closed Feedwater Heaters
- Product type
- Heat Exchanger Baffles and Support Plates
- Construction
- Machined from plate or forging to your drawing
Product description
Segmental baffles and tube support plates for shell-and-tube exchangers, stack-drilled to TEMA hole clearances and your drawing.
Specification
- Baffle tube-hole clearance: Tube OD + 0.8 mm (1/32 in) when unsupported span <= 914 mm or OD > 31.8 mm; OD + 0.4 mm (1/64 in) when span > 914 mm and OD <= 31.8 mm
- Baffle-hole over-tolerance: +0.010 in (0.25 mm; TEMA metric 0.3 mm) on 96% of holes; +0.015 in (0.4 mm) on remaining 4%
- Stack drilling: Baffles and supports are stack-drilled; stacks normally no deeper than 5 x drill diameter; drill drift about 0.0016 in per drill diameter of depth
- Tighter holes: Specifying holes tighter than TEMA/HEI raises cost and risks tube damage at insertion; zone design, larger entrance/exit areas, larger pitch or thicker baffles control vibration better
- Datasheet baffle fields: Cross-baffle type, cut % of diameter, vertical/horizontal cut, spacing, inlet spacing, longitudinal baffle seal, tube support type, U-bend support, bypass seals, impingement protection
- Hole finish: Burrs removed, workmanlike finish
Standards
TEMA, HEI Standards for Closed Feedwater Heaters. Equivalent grades across ASTM, EN, DIN, JIS and GB/T standards are indicative; we check them against each tender.
Testing and documents
- Dimensional check of hole size against the 96% / 4% rule
- Mill test certificate to EN 10204 3.1 on request; third-party inspection can be arranged against your inspection and test plan
Where it is used
- Replacement baffles and support plates during refinery and gas-plant retubing
Standard geometry
| Tube OD (in) | Tube OD (mm) | Baffle hole, unsupported span > 914 mm and OD <= 31.8 mm: OD + 0.4 mm (mm) | Baffle hole, span <= 914 mm or OD > 31.8 mm: OD + 0.8 mm (mm) | Same, in inches (OD + 1/64 in / OD + 1/32 in) | Over-tolerance, 96% of holes | Over-tolerance, max 4% of holes |
|---|---|---|---|---|---|---|
| 5/8 | 15.88 | 16.28 | 16.68 | 0.641 / 0.656 | +0.010 in (0.25 mm) | +0.015 in (0.38 mm) |
| 3/4 | 19.05 | 19.45 | 19.85 | 0.766 / 0.781 | +0.010 in (0.25 mm) | +0.015 in (0.38 mm) |
| 1 | 25.40 | 25.80 | 26.20 | 1.016 / 1.031 | +0.010 in (0.25 mm) | +0.015 in (0.38 mm) |
| 1-1/4 | 31.75 | 32.15 | 32.55 | 1.266 / 1.281 | +0.010 in (0.25 mm) | +0.015 in (0.38 mm) |
| 1-1/2 | 38.10 | n/a (OD > 31.8 mm) | 38.90 | - / 1.531 | +0.010 in (0.25 mm) | +0.015 in (0.38 mm) |
These are the limits of the standard, not part numbers. Each item is made to your drawing.
How we supply
Tube sheets, baffles and plates are made to the purchaser's drawing, so there is no catalogue part number for each size. We cut, machine, drill, ream and groove them from certified plate or forgings, stack-drill baffles and support plates so the holes line up through the bundle, and check hole size, pitch and ligaments against the drawing before dispatch. Send the drawing, or the material, the outside diameter, the thickness, the tube size and the pitch and layout, and we quote with the mill certificates and the inspection you need.
Ordering
Quote the Indus part number from the size table, or send the standard and grade, the outside diameter and wall (BWG or millimetres, minimum or average wall), the length and the quantity. We quote with the mill certificates and the inspection you need.
Identification
| Parameter | Value |
|---|---|
| Product type | Heat Exchanger Baffles and Support Plates |
| Construction | Machined from plate or forging to your drawing |
Compliance
| Parameter | Value |
|---|---|
| Standards | TEMA, HEI Standards for Closed Feedwater Heaters |
Dimensions
| Parameter | Value |
|---|---|
| Length | Random or fixed lengths; cut to length on request |
| Size table | Made to your drawing; standard geometry in the description |
Quality
| Parameter | Value |
|---|---|
| Testing | Dimensional check of hole size against the 96% / 4% rule |
| Certification | Mill test certificate to EN 10204 3.1 on request; third-party inspection by arrangement |
Application
| Parameter | Value |
|---|---|
| Typical services | Replacement baffles and support plates during refinery and gas-plant retubing |
Shipping & lead time
What are Heat Exchanger Baffles and Support Plates used for?▾
What sizes can Heat Exchanger Baffles and Support Plates be supplied in?▾
How are Heat Exchanger Baffles and Support Plates sized, and what do I send to get them quoted?▾
What hole clearances and tolerances apply to Heat Exchanger Baffles and Support Plates?▾
Why not specify tighter holes in Heat Exchanger Baffles and Support Plates than TEMA allows?▾
How are Heat Exchanger Baffles and Support Plates made?▾
Which standards and checks apply to Heat Exchanger Baffles and Support Plates?▾
What do Heat Exchanger Baffles and Support Plates connect to or work with?▾
How are the holes in Heat Exchanger Baffles and Support Plates drilled and checked?▾
When are Heat Exchanger Baffles and Support Plates ordered?▾
Can Heat Exchanger Baffles and Support Plates be supplied to customers outside the UAE?▾
Do you hold Heat Exchanger Baffles and Support Plates in stock, or are they made to order?▾
Shipped worldwide from our Dubai warehouse. Transit, routes and documentation for 136 destinations
From the blog

